Computer

Computer

From Wikipedia, the free encyclopedia
"Computer system" redirects here. For other uses, see Computer (disambiguation) and Computer system (disambiguation).
computer is a device that can be instructed to carry out an arbitrary set of arithmetic or logical operations automatically. The ability of computers to follow a sequence of operations, called a program, make computers very flexible and useful. Such computers are used as control systems for a very wide variety of industrial and consumer devices. This includes simple special purpose devices like microwave ovens and remote controls, factory devices such as industrial robots and computer assisted design, but also in general purpose devices like personal computers and mobile devices such as smartphones. The Internet is run on computers and it connects millions of other computers.
Since ancient times, simple manual devices like the abacus aided people in doing calculations. Early in the Industrial Revolution, some mechanical devices were built to automate long tedious tasks, such as guiding patterns for looms. More sophisticated electrical machines did specialized analog calculations in the early 20th century. The first digital electronic calculating machines were developed during World War II. The speed, power, and versatility of computers has increased continuously and dramatically since then.
Conventionally, a modern computer consists of at least one processing element, typically a central processing unit (CPU), and some form of memory. The processing element carries out arithmetic and logical operations, and a sequencing and control unit can change the order of operations in response to stored informationPeripheral devices include input devices (keyboards, mice, joystick, etc.), output devices (monitor screens, printers, etc.), and input/output devices that perform both functions (e.g., the 2000s-era touchscreen). Peripheral devices allow information to be retrieved from an external source and they enable the result of operations to be saved and retrieved.

Etymology

According to the Oxford English Dictionary, the first known use of the word "computer" was in 1613 in a book called The Yong Mans Gleanings by English writer Richard Braithwait: "I haue [sic] read the truest computer of Times, and the best Arithmetician that euer [sic] breathed, and he reduceth thy dayes into a short number." This usage of the term referred to a person who carried out calculations or computations. The word continued with the same meaning until the middle of the 20th century. From the end of the 19th century the word began to take on its more familiar meaning, a machine that carries out computations.[1]
The Online Etymology Dictionary gives the first attested use of "computer" in the "1640s, [meaning] "one who calculates,"; this is an "... agent noun from compute (v.)". The Online Etymology Dictionary states that the use of the term to mean "calculating machine" (of any type) is from 1897." The Online Etymology Dictionary indicates that the "modern use" of the term, to mean "programmable digital electronic computer" dates from "... 1945 under this name; [in a] theoretical [sense] from 1937, as Turing machine".[2]

History

Pre-20th century

Devices have been used to aid computation for thousands of years, mostly using one-to-one correspondence with fingers. The earliest counting device was probably a form of tally stick. Later record keeping aids throughout the Fertile Crescent included calculi (clay spheres, cones, etc.) which represented counts of items, probably livestock or grains, sealed in hollow unbaked clay containers.[3][4] The use of counting rods is one example.

The Chinese Suanpan (算盘) (the number represented on this abacus is 6,302,715,408)
The abacus was initially used for arithmetic tasks. The Roman abacus was developed from devices used in Babylonia as early as 2400 BC. Since then, many other forms of reckoning boards or tables have been invented. In a medieval European counting house, a checkered cloth would be placed on a table, and markers moved around on it according to certain rules, as an aid to calculating sums of money.

The ancient Greek-designed Antikythera mechanism, dating between 150 and 100 BC, is the world's oldest analog computer.
The Antikythera mechanism is believed to be the earliest mechanical analog "computer", according to Derek J. de Solla Price.[5] It was designed to calculate astronomical positions. It was discovered in 1901 in the Antikythera wreck off the Greek island of Antikythera, between Kythera and Crete, and has been dated to circa 100 BC. Devices of a level of complexity comparable to that of the Antikythera mechanism would not reappear until a thousand years later.
Many mechanical aids to calculation and measurement were constructed for astronomical and navigation use. The planisphere was a star chart invented by Abū Rayhān al-Bīrūnī in the early 11th century.[6] The astrolabe was invented in the Hellenistic world in either the 1st or 2nd centuries BC and is often attributed to Hipparchus. A combination of the planisphere and dioptra, the astrolabe was effectively an analog computer capable of working out several different kinds of problems in spherical astronomy. An astrolabe incorporating a mechanical calendar computer[7][8] and gear-wheels was invented by Abi Bakr of IsfahanPersia in 1235.[9] Abū Rayhān al-Bīrūnī invented the first mechanical geared lunisolar calendar astrolabe,[10] an early fixed-wired knowledge processing machine[11] with a gear train and gear-wheels,[12] circa 1000 AD.
The sector, a calculating instrument used for solving problems in proportion, trigonometry, multiplication and division, and for various functions, such as squares and cube roots, was developed in the late 16th century and found application in gunnery, surveying and navigation.
The planimeter was a manual instrument to calculate the area of a closed figure by tracing over it with a mechanical linkage.

A slide rule
The slide rule was invented around 1620–1630, shortly after the publication of the concept of the logarithm. It is a hand-operated analog computer for doing multiplication and division. As slide rule development progressed, added scales provided reciprocals, squares and square roots, cubes and cube roots, as well as transcendental functions such as logarithms and exponentials, circular and hyperbolictrigonometry and other functions. Aviation is one of the few fields where slide rules are still in widespread use, particularly for solving time–distance problems in light aircraft. To save space and for ease of reading, these are typically circular devices rather than the classic linear slide rule shape. A popular example is the E6B.
In the 1770s Pierre Jaquet-Droz, a Swiss watchmaker, built a mechanical doll (automata) that could write holding a quill pen. By switching the number and order of its internal wheels different letters, and hence different messages, could be produced. In effect, it could be mechanically "programmed" to read instructions. Along with two other complex machines, the doll is at the Musée d'Art et d'Histoire of NeuchâtelSwitzerland, and still operates.[13]
The tide-predicting machine invented by Sir William Thomson in 1872 was of great utility to navigation in shallow waters. It used a system of pulleys and wires to automatically calculate predicted tide levels for a set period at a particular location.
The differential analyser, a mechanical analog computer designed to solve differential equations by integration, used wheel-and-disc mechanisms to perform the integration. In 1876 Lord Kelvin had already discussed the possible construction of such calculators, but he had been stymied by the limited output torque of the ball-and-disk integrators.[14] In a differential analyzer, the output of one integrator drove the input of the next integrator, or a graphing output. The torque amplifier was the advance that allowed these machines to work. Starting in the 1920s, Vannevar Bush and others developed mechanical differential analyzers.

First computing device


A portion of Babbage's Difference engine.
Charles Babbage, an English mechanical engineer and polymath, originated the concept of a programmable computer. Considered the "father of the computer",[15] he conceptualized and invented the first mechanical computer in the early 19th century. After working on his revolutionary difference engine, designed to aid in navigational calculations, in 1833 he realized that a much more general design, an Analytical Engine, was possible. The input of programs and data was to be provided to the machine via punched cards, a method being used at the time to direct mechanical looms such as the Jacquard loom. For output, the machine would have a printer, a curve plotter and a bell. The machine would also be able to punch numbers onto cards to be read in later. The Engine incorporated an arithmetic logic unitcontrol flow in the form of conditional branching and loops, and integrated memory, making it the first design for a general-purpose computer that could be described in modern terms as Turing-complete.[16][17]
The machine was about a century ahead of its time. All the parts for his machine had to be made by hand — this was a major problem for a device with thousands of parts. Eventually, the project was dissolved with the decision of the British Government to cease funding. Babbage's failure to complete the analytical engine can be chiefly attributed to difficulties not only of politics and financing, but also to his desire to develop an increasingly sophisticated computer and to move ahead faster than anyone else could follow. Nevertheless, his son, Henry Babbage, completed a simplified version of the analytical engine's computing unit (the mill) in 1888. He gave a successful demonstration of its use in computing tables in 1906.

Analog computers


Sir William Thomson's third tide-predicting machine design, 1879–81
During the first half of the 20th century, many scientific computing needs were met by increasingly sophisticated analog computers, which used a direct mechanical or electrical model of the problem as a basis for computation. However, these were not programmable and generally lacked the versatility and accuracy of modern digital computers.[18] The first modern analog computer was a tide-predicting machine, invented by Sir William Thomson in 1872. The differential analyser, a mechanical analog computer designed to solve differential equations by integration using wheel-and-disc mechanisms, was conceptualized in 1876 by James Thomson, the brother of the more famous Lord Kelvin.[14]
The art of mechanical analog computing reached its zenith with the differential analyzer, built by H. L. Hazen and Vannevar Bush at MIT starting in 1927. This built on the mechanical integrators of James Thomson and the torque amplifiers invented by H. W. Nieman. A dozen of these devices were built before their obsolescence became obvious. By the 1950s the success of digital electronic computers had spelled the end for most analog computing machines, but analog computers remained in use during the 1950s in some specialized applications such as education (control systems) and aircraft (slide rule).

Digital computers

Electromechanical

By 1938 the United States Navy had developed an electromechanical analog computer small enough to use aboard a submarine. This was the Torpedo Data Computer, which used trigonometry to solve the problem of firing a torpedo at a moving target. During World War II similar devices were developed in other countries as well.

Replica of Zuse's Z3, the first fully automatic, digital (electromechanical) computer.
Early digital computers were electromechanical; electric switches drove mechanical relays to perform the calculation. These devices had a low operating speed and were eventually superseded by much faster all-electric computers, originally using vacuum tubes. The Z2, created by German engineer Konrad Zuse in 1939, was one of the earliest examples of an electromechanical relay computer.[19]
In 1941, Zuse followed his earlier machine up with the Z3, the world's first working electromechanical programmable, fully automatic digital computer.[20][21] The Z3 was built with 2000 relays, implementing a 22 bit word length that operated at a clock frequency of about 5–10 Hz.[22]Program code was supplied on punched film while data could be stored in 64 words of memory or supplied from the keyboard. It was quite similar to modern machines in some respects, pioneering numerous advances such as floating point numbers. Rather than the harder-to-implement decimal system (used in Charles Babbage's earlier design), using a binary system meant that Zuse's machines were easier to build and potentially more reliable, given the technologies available at that time.[23] The Z3 was Turing complete.[24][25]

Vacuum tubes and digital electronic circuits

Purely electronic circuit elements soon replaced their mechanical and electromechanical equivalents, at the same time that digital calculation replaced analog. The engineer Tommy Flowers, working at the Post Office Research Station in London in the 1930s, began to explore the possible use of electronics for the telephone exchange. Experimental equipment that he built in 1934 went into operation 5 years later, converting a portion of the telephone exchange network into an electronic data processing system, using thousands of vacuum tubes.[18] In the US, John Vincent Atanasoff and Clifford E. Berry of Iowa State University developed and tested the Atanasoff–Berry Computer (ABC) in 1942,[26] the first "automatic electronic digital computer".[27] This design was also all-electronic and used about 300 vacuum tubes, with capacitors fixed in a mechanically rotating drum for memory.[28]

Colossus was the first electronicdigital programmable computing device, and was used to break German ciphers during World War II.
During World War II, the British at Bletchley Park achieved a number of successes at breaking encrypted German military communications. The German encryption machine, Enigma, was first attacked with the help of the electro-mechanical bombes. To crack the more sophisticated German Lorenz SZ 40/42 machine, used for high-level Army communications, Max Newman and his colleagues commissioned Flowers to build the Colossus.[28] He spent eleven months from early February 1943 designing and building the first Colossus.[29] After a functional test in December 1943, Colossus was shipped to Bletchley Park, where it was delivered on 18 January 1944[30] and attacked its first message on 5 February.[28]
Colossus was the world's first electronic digital programmable computer.[18] It used a large number of valves (vacuum tubes). It had paper-tape input and was capable of being configured to perform a variety of boolean logical operations on its data, but it was not Turing-complete. Nine Mk II Colossi were built (The Mk I was converted to a Mk II making ten machines in total). Colossus Mark I contained 1500 thermionic valves (tubes), but Mark II with 2400 valves, was both 5 times faster and simpler to operate than Mark 1, greatly speeding the decoding process.[31][32]

ENIAC was the first Turing-complete device, and performed ballistics trajectory calculations for the United States Army.
The U.S.-built ENIAC[33] (Electronic Numerical Integrator and Computer) was the first electronic programmable computer built in the US. Although the ENIAC was similar to the Colossus it was much faster and more flexible. Like the Colossus, a "program" on the ENIAC was defined by the states of its patch cables and switches, a far cry from the stored program electronic machines that came later. Once a program was written, it had to be mechanically set into the machine with manual resetting of plugs and switches.
It combined the high speed of electronics with the ability to be programmed for many complex problems. It could add or subtract 5000 times a second, a thousand times faster than any other machine. It also had modules to multiply, divide, and square root. High speed memory was limited to 20 words (about 80 bytes). Built under the direction of John Mauchly and J. Presper Eckert at the University of Pennsylvania, ENIAC's development and construction lasted from 1943 to full operation at the end of 1945. The machine was huge, weighing 30 tons, using 200 kilowatts of electric power and contained over 18,000 vacuum tubes, 1,500 relays, and hundreds of thousands of resistors, capacitors, and inductors.[34]

Modern computers

Concept of modern computer

The principle of the modern computer was proposed by Alan Turing in his seminal 1936 paper,[35] On Computable Numbers. Turing proposed a simple device that he called "Universal Computing machine" and that is now known as a universal Turing machine. He proved that such a machine is capable of computing anything that is computable by executing instructions (program) stored on tape, allowing the machine to be programmable. The fundamental concept of Turing's design is the stored program, where all the instructions for computing are stored in memory. Von Neumann acknowledged that the central concept of the modern computer was due to this paper.[36] Turing machines are to this day a central object of study in theory of computation. Except for the limitations imposed by their finite memory stores, modern computers are said to be Turing-complete, which is to say, they have algorithm execution capability equivalent to a universal Turing machine.

Stored programs

Three tall racks containing electronic circuit boards
A section of the Manchester Small-Scale Experimental Machine, the first stored-program computer.
Early computing machines had fixed programs. Changing its function required the re-wiring and re-structuring of the machine.[28] With the proposal of the stored-program computer this changed. A stored-program computer includes by design an instruction set and can store in memory a set of instructions (a program) that details the computation. The theoretical basis for the stored-program computer was laid by Alan Turing in his 1936 paper. In 1945 Turing joined the National Physical Laboratory and began work on developing an electronic stored-program digital computer. His 1945 report "Proposed Electronic Calculator" was the first specification for such a device. John von Neumann at the University of Pennsylvania also circulated his First Draft of a Report on the EDVAC in 1945.[18]

Ferranti Mark 1, c. 1951.
The Manchester Small-Scale Experimental Machine, nicknamed Baby, was the world's first stored-program computer. It was built at the Victoria University of Manchester by Frederic C. WilliamsTom Kilburn and Geoff Tootill, and ran its first program on 21 June 1948.[37] It was designed as a testbed for the Williams tube, the first random-access digital storage device.[38] Although the computer was considered "small and primitive" by the standards of its time, it was the first working machine to contain all of the elements essential to a modern electronic computer.[39] As soon as the SSEM had demonstrated the feasibility of its design, a project was initiated at the university to develop it into a more usable computer, the Manchester Mark 1.
The Mark 1 in turn quickly became the prototype for the Ferranti Mark 1, the world's first commercially available general-purpose computer.[40]Built by Ferranti, it was delivered to the University of Manchester in February 1951. At least seven of these later machines were delivered between 1953 and 1957, one of them to Shell labs in Amsterdam.[41] In October 1947, the directors of British catering company J. Lyons & Company decided to take an active role in promoting the commercial development of computers. The LEO I computer became operational in April 1951[42] and ran the world's first regular routine office computer job.

Transistors

The bipolar transistor was invented in 1947. From 1955 onwards transistors replaced vacuum tubes in computer designs, giving rise to the "second generation" of computers. Compared to vacuum tubes, transistors have many advantages: they are smaller, and require less power than vacuum tubes, so give off less heat. Silicon junction transistors were much more reliable than vacuum tubes and had longer, indefinite, service life. Transistorized computers could contain tens of thousands of binary logic circuits in a relatively compact space.
At the University of Manchester, a team under the leadership of Tom Kilburn designed and built a machine using the newly developed transistors instead of valves.[43] Their first transistorised computer and the first in the world, was operational by 1953, and a second version was completed there in April 1955. However, the machine did make use of valves to generate its 125 kHz clock waveforms and in the circuitry to read and write on its magnetic drum memory, so it was not the first completely transistorized computer. That distinction goes to the Harwell CADET of 1955,[44] built by the electronics division of the Atomic Energy Research Establishment at Harwell.[44][45]

Integrated circuits

The next great advance in computing power came with the advent of the integrated circuit. The idea of the integrated circuit was first conceived by a radar scientist working for the Royal Radar Establishment of the Ministry of DefenceGeoffrey W.A. Dummer. Dummer presented the first public description of an integrated circuit at the Symposium on Progress in Quality Electronic Components in Washington, D.C. on 7 May 1952.[46]
The first practical ICs were invented by Jack Kilby at Texas Instruments and Robert Noyce at Fairchild Semiconductor.[47] Kilby recorded his initial ideas concerning the integrated circuit in July 1958, successfully demonstrating the first working integrated example on 12 September 1958.[48] In his patent application of 6 February 1959, Kilby described his new device as "a body of semiconductor material ... wherein all the components of the electronic circuit are completely integrated".[49][50] Noyce also came up with his own idea of an integrated circuit half a year later than Kilby.[51] His chip solved many practical problems that Kilby's had not. Produced at Fairchild Semiconductor, it was made of silicon, whereas Kilby's chip was made of germanium.
This new development heralded an explosion in the commercial and personal use of computers and led to the invention of the microprocessor. While the subject of exactly which device was the first microprocessor is contentious, partly due to lack of agreement on the exact definition of the term "microprocessor", it is largely undisputed that the first single-chip microprocessor was the Intel 4004,[52] designed and realized by Ted HoffFederico Faggin, and Stanley Mazor at Intel.[53]

Mobile computers become dominant

With the continued miniaturization of computing resources, and advancements in portable battery life, portable computers grew in popularity in the 2000s.[54] The same developments that spurred the growth of laptop computers and other portable computers allowed manufacturers to integrate computing resources into cellular phones. These so-called smartphones and tablets run on a variety of operating systems and have become the dominant computing device on the market, with manufacturers reporting having shipped an estimated 237 million devices in 2Q 2013.[55]

Programs

The defining feature of modern computers which distinguishes them from all other machines is that they can be programmed. That is to say that some type of instructions (the program) can be given to the computer, and it will process them. Modern computers based on the von Neumann architecture often have machine code in the form of an imperative programming language. In practical terms, a computer program may be just a few instructions or extend to many millions of instructions, as do the programs for word processors and web browsers for example. A typical modern computer can execute billions of instructions per second (gigaflops) and rarely makes a mistake over many years of operation. Large computer programs consisting of several million instructions may take teams of programmers years to write, and due to the complexity of the task almost certainly contain errors.

Stored program architecture

Main articles: Computer program and Computer programming

Replica of the Small-Scale Experimental Machine (SSEM), the world's first stored-program computer, at the Museum of Science and Industry in Manchester, England
This section applies to most common RAM machine-based computers.
In most cases, computer instructions are simple: add one number to another, move some data from one location to another, send a message to some external device, etc. These instructions are read from the computer's memory and are generally carried out (executed) in the order they were given. However, there are usually specialized instructions to tell the computer to jump ahead or backwards to some other place in the program and to carry on executing from there. These are called "jump" instructions (or branches). Furthermore, jump instructions may be made to happen conditionally so that different sequences of instructions may be used depending on the result of some previous calculation or some external event. Many computers directly support subroutines by providing a type of jump that "remembers" the location it jumped from and another instruction to return to the instruction following that jump instruction.
Program execution might be likened to reading a book. While a person will normally read each word and line in sequence, they may at times jump back to an earlier place in the text or skip sections that are not of interest. Similarly, a computer may sometimes go back and repeat the instructions in some section of the program over and over again until some internal condition is met. This is called the flow of control within the program and it is what allows the computer to perform tasks repeatedly without human intervention.
Comparatively, a person using a pocket calculator can perform a basic arithmetic operation such as adding two numbers with just a few button presses. But to add together all of the numbers from 1 to 1,000 would take thousands of button presses and a lot of time, with a near certainty of making a mistake. On the other hand, a computer may be programmed to do this with just a few simple instructions. The following example is written in the MIPS assembly language:
  begin:
  addi $8, $0, 0           # initialize sum to 0
  addi $9, $0, 1           # set first number to add = 1
  loop:
  slti $10, $9, 1000       # check if the number is less than 1000
  beq $10, $0, finish      # if odd number is greater than n then exit
  add $8, $8, $9           # update sum
  addi $9, $9, 1           # get next number
  j loop                   # repeat the summing process
  finish:
  add $2, $8, $0           # put sum in output register
Once told to run this program, the computer will perform the repetitive addition task without further human intervention. It will almost never make a mistake and a modern PC can complete the task in a fraction of a second.

Machine code

In most computers, individual instructions are stored as machine code with each instruction being given a unique number (its operation code or opcode for short). The command to add two numbers together would have one opcode; the command to multiply them would have a different opcode, and so on. The simplest computers are able to perform any of a handful of different instructions; the more complex computers have several hundred to choose from, each with a unique numerical code. Since the computer's memory is able to store numbers, it can also store the instruction codes. This leads to the important fact that entire programs (which are just lists of these instructions) can be represented as lists of numbers and can themselves be manipulated inside the computer in the same way as numeric data. The fundamental concept of storing programs in the computer's memory alongside the data they operate on is the crux of the von Neumann, or stored program[citation needed], architecture. In some cases, a computer might store some or all of its program in memory that is kept separate from the data it operates on. This is called the Harvard architecture after the Harvard Mark I computer. Modern von Neumann computers display some traits of the Harvard architecture in their designs, such as in CPU caches.
While it is possible to write computer programs as long lists of numbers (machine language) and while this technique was used with many early computers,[56] it is extremely tedious and potentially error-prone to do so in practice, especially for complicated programs. Instead, each basic instruction can be given a short name that is indicative of its function and easy to remember – a mnemonic such as ADD, SUB, MULT or JUMP. These mnemonics are collectively known as a computer's assembly language. Converting programs written in assembly language into something the computer can actually understand (machine language) is usually done by a computer program called an assembler.

A 1970s punched card containing one line from a FORTRAN program. The card reads: "Z(1) = Y + W(1)" and is labeled "PROJ039" for identification purposes.

Programming language

Main article: Programming language
Programming languages provide various ways of specifying programs for computers to run. Unlike natural languages, programming languages are designed to permit no ambiguity and to be concise. They are purely written languages and are often difficult to read aloud. They are generally either translated into machine code by a compiler or an assembler before being run, or translated directly at run time by an interpreter. Sometimes programs are executed by a hybrid method of the two techniques.

Low-level languages

Machine languages and the assembly languages that represent them (collectively termed low-level programming languages) tend to be unique to a particular type of computer. For instance, an ARM architecture computer (such as may be found in a smartphone or a hand-held videogame) cannot understand the machine language of an x86 CPU that might be in a PC.[57]

High-level languages/third generation language

Though considerably easier than in machine language, writing long programs in assembly language is often difficult and is also error prone. Therefore, most practical programs are written in more abstract high-level programming languages that are able to express the needs of the programmer more conveniently (and thereby help reduce programmer error). High level languages are usually "compiled" into machine language (or sometimes into assembly language and then into machine language) using another computer program called a compiler.[58] High level languages are less related to the workings of the target computer than assembly language, and more related to the language and structure of the problem(s) to be solved by the final program. It is therefore often possible to use different compilers to translate the same high level language program into the machine language of many different types of computer. This is part of the means by which software like video games may be made available for different computer architectures such as personal computers and various video game consoles.

Fourth generation languages

These 4G languages are less procedural than 3G languages. The benefit of 4GL is that they provide ways to obtain information without requiring the direct help of a programmer. An example of a 4GL is SQL.

Program design

Program design of small programs is relatively simple and involves the analysis of the problem, collection of inputs, using the programming constructs within languages, devising or using established procedures and algorithms, providing data for output devices and solutions to the problem as applicable. As problems become larger and more complex, features such as subprograms, modules, formal documentation, and new paradigms such as object-oriented programming are encountered. Large programs involving thousands of line of code and more require formal software methodologies. The task of developing large software systems presents a significant intellectual challenge. Producing software with an acceptably high reliability within a predictable schedule and budget has historically been difficult; the academic and professional discipline of software engineering concentrates specifically on this challenge.

Bugs

Main article: Software bug

The actual first computer bug, a moth found trapped on a relay of the Harvard Mark II computer
Errors in computer programs are called "bugs". They may be benign and not affect the usefulness of the program, or have only subtle effects. But in some cases, they may cause the program or the entire system to "hang", becoming unresponsive to input such as mouse clicks or keystrokes, to completely fail, or to crash. Otherwise benign bugs may sometimes be harnessed for malicious intent by an unscrupulous user writing an exploit, code designed to take advantage of a bug and disrupt a computer's proper execution. Bugs are usually not the fault of the computer. Since computers merely execute the instructions they are given, bugs are nearly always the result of programmer error or an oversight made in the program's design.[59] Admiral Grace Hopper, an American computer scientist and developer of the first compiler, is credited for having first used the term "bugs" in computing after a dead moth was found shorting a relay in the Harvard Mark II computer in September 1947.[60]

Components

File:Computer Components.webm
Video demonstrating the standard components of a "slimline" computer
A general purpose computer has four main components: the arithmetic logic unit (ALU), the control unit, the memory, and the input and output devices (collectively termed I/O). These parts are interconnected by buses, often made of groups of wires. Inside each of these parts are thousands to trillions of small electrical circuits which can be turned off or on by means of an electronic switch. Each circuit represents a bit (binary digit) of information so that when the circuit is on it represents a "1", and when off it represents a "0" (in positive logic representation). The circuits are arranged in logic gates so that one or more of the circuits may control the state of one or more of the other circuits.

Control unit

Main articles: CPU design and Control unit

Diagram showing how a particular MIPS architecture instruction would be decoded by the control system
The control unit (often called a control system or central controller) manages the computer's various components; it reads and interprets (decodes) the program instructions, transforming them into control signals that activate other parts of the computer.[61] Control systems in advanced computers may change the order of execution of some instructions to improve performance.
A key component common to all CPUs is the program counter, a special memory cell (a register) that keeps track of which location in memory the next instruction is to be read from.[62]
The control system's function is as follows—note that this is a simplified description, and some of these steps may be performed concurrently or in a different order depending on the type of CPU:
  1. Read the code for the next instruction from the cell indicated by the program counter.
  2. Decode the numerical code for the instruction into a set of commands or signals for each of the other systems.
  3. Increment the program counter so it points to the next instruction.
  4. Read whatever data the instruction requires from cells in memory (or perhaps from an input device). The location of this required data is typically stored within the instruction code.
  5. Provide the necessary data to an ALU or register.
  6. If the instruction requires an ALU or specialized hardware to complete, instruct the hardware to perform the requested operation.
  7. Write the result from the ALU back to a memory location or to a register or perhaps an output device.
  8. Jump back to step (1).
Since the program counter is (conceptually) just another set of memory cells, it can be changed by calculations done in the ALU. Adding 100 to the program counter would cause the next instruction to be read from a place 100 locations further down the program. Instructions that modify the program counter are often known as "jumps" and allow for loops (instructions that are repeated by the computer) and often conditional instruction execution (both examples of control flow).
The sequence of operations that the control unit goes through to process an instruction is in itself like a short computer program, and indeed, in some more complex CPU designs, there is another yet smaller computer called a microsequencer, which runs a microcode program that causes all of these events to happen.

Central processing unit (CPU)

The control unit, ALU, and registers are collectively known as a central processing unit (CPU). Early CPUs were composed of many separate components but since the mid-1970s CPUs have typically been constructed on a single integrated circuit called a microprocessor.

Arithmetic logic unit (ALU)

Main article: Arithmetic logic unit
The ALU is capable of performing two classes of operations: arithmetic and logic.[63] The set of arithmetic operations that a particular ALU supports may be limited to addition and subtraction, or might include multiplication, division, trigonometry functions such as sine, cosine, etc., and square roots. Some can only operate on whole numbers (integers) whilst others use floating point to represent real numbers, albeit with limited precision. However, any computer that is capable of performing just the simplest operations can be programmed to break down the more complex operations into simple steps that it can perform. Therefore, any computer can be programmed to perform any arithmetic operation—although it will take more time to do so if its ALU does not directly support the operation. An ALU may also compare numbers and return boolean truth values (true or false) depending on whether one is equal to, greater than or less than the other ("is 64 greater than 65?"). Logic operations involve Boolean logicANDORXOR, and NOT. These can be useful for creating complicated conditional statements and processing boolean logic.
Superscalar computers may contain multiple ALUs, allowing them to process several instructions simultaneously.[64] Graphics processors and computers with SIMD and MIMD features often contain ALUs that can perform arithmetic on vectors and matrices.

Memory

Main article: Computer data storage

Magnetic core memory was the computer memory of choice throughout the 1960s, until it was replaced by semiconductor memory.
A computer's memory can be viewed as a list of cells into which numbers can be placed or read. Each cell has a numbered "address" and can store a single number. The computer can be instructed to "put the number 123 into the cell numbered 1357" or to "add the number that is in cell 1357 to the number that is in cell 2468 and put the answer into cell 1595." The information stored in memory may represent practically anything. Letters, numbers, even computer instructions can be placed into memory with equal ease. Since the CPU does not differentiate between different types of information, it is the software's responsibility to give significance to what the memory sees as nothing but a series of numbers.
In almost all modern computers, each memory cell is set up to store binary numbers in groups of eight bits (called a byte). Each byte is able to represent 256 different numbers (28 = 256); either from 0 to 255 or −128 to +127. To store larger numbers, several consecutive bytes may be used (typically, two, four or eight). When negative numbers are required, they are usually stored in two's complement notation. Other arrangements are possible, but are usually not seen outside of specialized applications or historical contexts. A computer can store any kind of information in memory if it can be represented numerically. Modern computers have billions or even trillions of bytes of memory.
The CPU contains a special set of memory cells called registers that can be read and written to much more rapidly than the main memory area. There are typically between two and one hundred registers depending on the type of CPU. Registers are used for the most frequently needed data items to avoid having to access main memory every time data is needed. As data is constantly being worked on, reducing the need to access main memory (which is often slow compared to the ALU and control units) greatly increases the computer's speed.
Computer main memory comes in two principal varieties:
RAM can be read and written to anytime the CPU commands it, but ROM is preloaded with data and software that never changes, therefore the CPU can only read from it. ROM is typically used to store the computer's initial start-up instructions. In general, the contents of RAM are erased when the power to the computer is turned off, but ROM retains its data indefinitely. In a PC, the ROM contains a specialized program called the BIOS that orchestrates loading the computer's operating system from the hard disk drive into RAM whenever the computer is turned on or reset. In embedded computers, which frequently do not have disk drives, all of the required software may be stored in ROM. Software stored in ROM is often called firmware, because it is notionally more like hardware than software. Flash memory blurs the distinction between ROM and RAM, as it retains its data when turned off but is also rewritable. It is typically much slower than conventional ROM and RAM however, so its use is restricted to applications where high speed is unnecessary.[65]
In more sophisticated computers there may be one or more RAM cache memories, which are slower than registers but faster than main memory. Generally computers with this sort of cache are designed to move frequently needed data into the cache automatically, often without the need for any intervention on the programmer's part.

Input/output (I/O)

Main article: Input/output

Hard disk drives are common storage devices used with computers.
I/O is the means by which a computer exchanges information with the outside world.[66] Devices that provide input or output to the computer are called peripherals.[67] On a typical personal computer, peripherals include input devices like the keyboard and mouse, and output devices such as the display and printerHard disk drivesfloppy disk drives and optical disc drives serve as both input and output devices. Computer networking is another form of I/O. I/O devices are often complex computers in their own right, with their own CPU and memory. A graphics processing unit might contain fifty or more tiny computers that perform the calculations necessary to display 3D graphics.[citation needed] Modern desktop computers contain many smaller computers that assist the main CPU in performing I/O. A 2016-era flat screen display contains its own computer circuitry.

Multitasking

Main article: Computer multitasking
While a computer may be viewed as running one gigantic program stored in its main memory, in some systems it is necessary to give the appearance of running several programs simultaneously. This is achieved by multitasking i.e. having the computer switch rapidly between running each program in turn.[68] One means by which this is done is with a special signal called an interrupt, which can periodically cause the computer to stop executing instructions where it was and do something else instead. By remembering where it was executing prior to the interrupt, the computer can return to that task later. If several programs are running "at the same time". then the interrupt generator might be causing several hundred interrupts per second, causing a program switch each time. Since modern computers typically execute instructions several orders of magnitude faster than human perception, it may appear that many programs are running at the same time even though only one is ever executing in any given instant. This method of multitasking is sometimes termed "time-sharing" since each program is allocated a "slice" of time in turn.[69]
Before the era of inexpensive computers, the principal use for multitasking was to allow many people to share the same computer. Seemingly, multitasking would cause a computer that is switching between several programs to run more slowly, in direct proportion to the number of programs it is running, but most programs spend much of their time waiting for slow input/output devices to complete their tasks. If a program is waiting for the user to click on the mouse or press a key on the keyboard, then it will not take a "time slice" until the event it is waiting for has occurred. This frees up time for other programs to execute so that many programs may be run simultaneously without unacceptable speed loss.

Multiprocessing

Main article: Multiprocessing

Cray designed many supercomputers that used multiprocessing heavily.
Some computers are designed to distribute their work across several CPUs in a multiprocessing configuration, a technique once employed only in large and powerful machines such as supercomputersmainframe computers and servers. Multiprocessor and multi-core (multiple CPUs on a single integrated circuit) personal and laptop computers are now widely available, and are being increasingly used in lower-end markets as a result.
Supercomputers in particular often have highly unique architectures that differ significantly from the basic stored-program architecture and from general purpose computers.[70] They often feature thousands of CPUs, customized high-speed interconnects, and specialized computing hardware. Such designs tend to be useful only for specialized tasks due to the large scale of program organization required to successfully utilize most of the available resources at once. Supercomputers usually see usage in large-scale simulationgraphics rendering, and cryptography applications, as well as with other so-called "embarrassingly parallel" tasks.

Networking and the Internet

Main articles: Computer networking and Internet

Visualization of a portion of the routes on the Internet
Computers have been used to coordinate information between multiple locations since the 1950s. The U.S. military's SAGE system was the first large-scale example of such a system, which led to a number of special-purpose commercial systems such as Sabre.[71] In the 1970s, computer engineers at research institutions throughout the United States began to link their computers together using telecommunications technology. The effort was funded by ARPA (now DARPA), and the computer network that resulted was called the ARPANET.[72] The technologies that made the Arpanet possible spread and evolved.
In time, the network spread beyond academic and military institutions and became known as the Internet. The emergence of networking involved a redefinition of the nature and boundaries of the computer. Computer operating systems and applications were modified to include the ability to define and access the resources of other computers on the network, such as peripheral devices, stored information, and the like, as extensions of the resources of an individual computer. Initially these facilities were available primarily to people working in high-tech environments, but in the 1990s the spread of applications like e-mail and the World Wide Web, combined with the development of cheap, fast networking technologies like Ethernet and ADSL saw computer networking become almost ubiquitous. In fact, the number of computers that are networked is growing phenomenally. A very large proportion of personal computers regularly connect to the Internet to communicate and receive information. "Wireless" networking, often utilizing mobile phone networks, has meant networking is becoming increasingly ubiquitous even in mobile computing environments.

Computer architecture paradigms

There are many types of computer architectures:
Of all these abstract machines, a quantum computer holds the most promise for revolutionizing computing.[73] Logic gates are a common abstraction which can apply to most of the above digital or analog paradigms. The ability to store and execute lists of instructions called programs makes computers extremely versatile, distinguishing them from calculators. The Church–Turing thesis is a mathematical statement of this versatility: any computer with a minimum capability (being Turing-complete) is, in principle, capable of performing the same tasks that any other computer can perform. Therefore, any type of computer (netbooksupercomputercellular automaton, etc.) is able to perform the same computational tasks, given enough time and storage capacity.

Misconceptions

Main articles: Human computer and Harvard Computers

Women as computers in NACA High Speed Flight Station "Computer Room"
A computer does not need to be electronic, nor even have a processor, nor RAM, nor even a hard disk. While popular usage of the word "computer" is synonymous with a personal electronic computer, the modern[74] definition of a computer is literally: "A device that computes, especially a programmable [usually] electronic machine that performs high-speed mathematical or logical operations or that assembles, stores, correlates, or otherwise processes information."[75] Any device which processes information qualifies as a computer, especially if the processing is purposeful.[citation needed]

Unconventional computing

Main article: Unconventional computing
Historically, computers evolved from mechanical computers and eventually from vacuum tubes to transistors. However, conceptually computational systems as flexible as a personal computer can be built out of almost anything. For example, a computer can be made out of billiard balls (billiard ball computer); an often quoted example.[citation needed] More realistically, modern computers are made out of transistors made of photolithographed semiconductors.

Future

There is active research to make computers out of many promising new types of technology, such as optical computersDNA computersneural computers, and quantum computers. Most computers are universal, and are able to calculate any computable function, and are limited only by their memory capacity and operating speed. However different designs of computers can give very different performance for particular problems; for example quantum computers can potentially break some modern encryption algorithms (by quantum factoring) very quickly.

Further topics

Artificial intelligence

A computer will solve problems in exactly the way it is programmed to, without regard to efficiency, alternative solutions, possible shortcuts, or possible errors in the code. Computer programs that learn and adapt are part of the emerging field of artificial intelligence and machine learning.

Hardware

The term hardware covers all of those parts of a computer that are tangible physical objects. Circuits, computer chips, graphic cards, sound cards, memory (RAM), motherboard, displays, power supplies, cables, keyboards, printers and "mice" input devices are all hardware.

History of computing hardware

First generation (mechanical/electromechanical)CalculatorsPascal's calculatorArithmometerDifference engineQuevedo's analytical machines
Programmable devicesJacquard loomAnalytical engineIBM ASCC/Harvard Mark IHarvard Mark IIIBM SSECZ1Z2Z3
Second generation (vacuum tubes)CalculatorsAtanasoff–Berry ComputerIBM 604UNIVAC 60UNIVAC 120
Programmable devicesColossusENIACManchester Small-Scale Experimental MachineEDSACManchester Mark 1Ferranti PegasusFerranti MercuryCSIRACEDVACUNIVAC IIBM 701IBM 702IBM 650Z22
Third generation (discrete transistors and SSI, MSI, LSI integrated circuits)MainframesIBM 7090IBM 7080IBM System/360BUNCH
MinicomputerHP 2116AIBM System/32IBM System/36LINCPDP-8PDP-11
Fourth generation (VLSI integrated circuits)MinicomputerVAXIBM System i
4-bit microcomputerIntel 4004Intel 4040
8-bit microcomputerIntel 8008Intel 8080Motorola 6800Motorola 6809MOS Technology 6502Zilog Z80
16-bit microcomputerIntel 8088Zilog Z8000WDC 65816/65802
32-bit microcomputerIntel 80386PentiumMotorola 68000ARM
64-bit microcomputer[76]AlphaMIPSPA-RISCPowerPCSPARCx86-64ARMv8-A
Embedded computerIntel 8048Intel 8051
Personal computerDesktop computerHome computerLaptop computerPersonal digital assistant (PDA), Portable computerTablet PCWearable computer
Theoretical/experimentalQuantum computerChemical computerDNA computingOptical computerSpintronics based computer

Other hardware topics

Peripheral device (input/output)InputMousekeyboardjoystickimage scannerwebcamgraphics tabletmicrophone
OutputMonitorprinterloudspeaker
BothFloppy disk drivehard disk driveoptical disc drive, teleprinter
Computer busesShort rangeRS-232SCSIPCIUSB
Long range (computer networking)EthernetATMFDDI

Software

Main article: Computer software
Software refers to parts of the computer which do not have a material form, such as programs, data, protocols, etc. Software is that part of a computer system that consists of encoded information or computer instructions, in contrast to the physical hardware from which the system is built. Computer software includes computer programslibraries and related non-executable data, such as online documentation or digital media. Computer hardware and software require each other and neither can be realistically used on its own. When software is stored in hardware that cannot easily be modified, such as with BIOS ROM in an IBM PC compatible) computer, it is sometimes called "firmware".
Operating system /System SoftwareUnix and BSDUNIX System VIBM AIXHP-UXSolaris (SunOS), IRIXList of BSD operating systems
GNU/LinuxList of Linux distributionsComparison of Linux distributions
Microsoft WindowsWindows 95Windows 98Windows NTWindows 2000Windows MeWindows XPWindows VistaWindows 7Windows 8Windows 10
DOS86-DOS (QDOS), IBM PC DOSMS-DOSDR-DOSFreeDOS
Mac OSMac OS classicMac OS X
Embedded and real-timeList of embedded operating systems
ExperimentalAmoebaOberon/BluebottlePlan 9 from Bell Labs
LibraryMultimediaDirectXOpenGLOpenALVulkan (API)
Programming libraryC standard libraryStandard Template Library
DataProtocolTCP/IPKermitFTPHTTPSMTP
File formatHTMLXMLJPEGMPEGPNG
User interfaceGraphical user interface (WIMP)Microsoft WindowsGNOMEKDEQNX PhotonCDEGEMAqua
Text-based user interfaceCommand-line interfaceText user interface
Application SoftwareOffice suiteWord processingDesktop publishingPresentation programDatabase management system, Scheduling & Time management, SpreadsheetAccounting software
Internet AccessBrowserE-mail clientWeb serverMail transfer agentInstant messaging
Design and manufacturingComputer-aided designComputer-aided manufacturing, Plant management, Robotic manufacturing, Supply chain management
GraphicsRaster graphics editorVector graphics editor3D modelerAnimation editor3D computer graphicsVideo editingImage processing
AudioDigital audio editorAudio playbackMixingAudio synthesisComputer music
Software engineeringCompilerAssemblerInterpreterDebuggerText editorIntegrated development environmentSoftware performance analysisRevision controlSoftware configuration management
EducationalEdutainmentEducational gameSerious gameFlight simulator
GamesStrategyArcadePuzzleSimulationFirst-person shooterPlatformMassively multiplayerInteractive fiction
MiscArtificial intelligenceAntivirus softwareMalware scannerInstaller/Package management systemsFile manager

Languages

There are thousands of different programming languages—some intended to be general purpose, others useful only for highly specialized applications.
Programming languages
Lists of programming languagesTimeline of programming languagesList of programming languages by categoryGenerational list of programming languagesList of programming languagesNon-English-based programming languages
Commonly used assembly languagesARMMIPSx86
Commonly used high-level programming languagesAdaBASICCC++C#COBOLFortranPL/1REXXJavaLispPascalObject Pascal
Commonly used scripting languagesBourne scriptJavaScriptPythonRubyPHPPerl

Firmware

Firmware is the technology which has the combination of both hardware and software such as BIOS chip inside a computer. This chip (hardware) is located on the motherboard and has the BIOS set up (software) stored in it.

Types

Computers are typically classified based on their uses:

Based on uses

Based on sizes

Input devices

When unprocessed data is sent to the computer with the help of input devices, the data is processed and sent to output devices. The input devices may be hand-operated or automated. The act of processing is mainly regulated by the CPU. Some examples of hand-operated input devices are:

Output devices

The means through which computer gives output are known as output devices. Some examples of output devices are:

Professions and organizations

As the use of computers has spread throughout society, there are an increasing number of careers involving computers.
Computer-related professions
Hardware-relatedElectrical engineeringElectronic engineeringComputer engineeringTelecommunications engineeringOptical engineeringNanoengineering
Software-relatedComputer scienceComputer engineeringDesktop publishingHuman–computer interactionInformation technologyInformation systemsComputational scienceSoftware engineeringVideo game industryWeb design
The need for computers to work well together and to be able to exchange information has spawned the need for many standards organizations, clubs and societies of both a formal and informal nature.
Organizations
Standards groupsANSIIECIEEEIETFISOW3C
Professional societiesACMAISIETIFIPBCS
Free/open source software groupsFree Software FoundationMozilla FoundationApache Software Foundation

See also


Computer

From Wikipedia, the free encyclopedia

This article has many issues. Please help fix them or discuss these issues on the talk page.


A drawing of a usual modern desktop computer.
computer is a machine (mostly electronic) that is able to take information (input), do some work on or make changes to the information (process), to make new information (output). Computers have existed for much of human history. Examples of early computers are the astrolabe and the abacus. There are four main processing steps in a computer, and they are: inputtingoutputtingstorage and processing.
Modern computers are very different from early computers. They can do billions of calculations per second. Most people have used a personal computer in their home or at work. Computers do many different jobs where automation is useful. Some examples are controlling traffic lightsvehicle computers, security systems, washing machines and digital televisions.
computer user can control it by a user interfaceInput devices include keyboardmouse, buttons, touch screen. Some very new computers can also be controlled with voice commands or hand gestures or even brain signals through electrodes implanted in the brain or along nerves.
Computers can be designed to do almost anything with information. Computers are used to control large and small machines which in the past were controlled by humans. They are also in homes, where they are used for things such as listening to music, reading the news, and writing.
Modern computers are electronic computer hardware but they are only useful if they also have software. The software uses the hardware when the user gives it instructions, and gives useful output.
Many modern computers do billions of calculations each second. They do mathematical arithmetic very quickly but computers do not really "think". They only follow the instructions in their software programs.
Computer programs are designed or written by computer programmers. A few programmers write programs in the computer's own language called machine code. Most programs are written using a programming language like C++Java, and Python. These programming languages are more like the language you talk and write with every day. A program called a compiler translates the user's instructions into binary code (machine code) that the computer will understand and do what is needed.

History of computers[change | change source]


The Jacquard loom was one of the first programmable devices.

Definition[change | change source]

A computer is an electronic machine which helps in solving problems quickly and easily. It solves problems according to instructions given to it by the computer user called programs or software. It is a digital machine(that uses binary digits) used in all fields.

Automation[change | change source]

Humans have a problem with maths. To show this, try doing 584 x 3,220 in your head. It is hard to remember all the steps! People made tools to help them remember where they were in a maths problem. The other problem people have is that they have to do the same problem over and over and over again. A cashier had to make change every day in her head or with a piece of paper. That took a lot of time and made mistakes. So, people made calculators that did those same things over and over. This part of computer history is called the "history of automated calculation," which is a fancy phrase for "the history of machines that make it easy for me to do this same maths problem over and over without making mistakes."
The abacus, the slide rule, the astrolabe and the Antikythera mechanism (which dates from about 150-100 BC) are examples of automated calculation machines.

Programming[change | change source]

People did not want a machine that would do the same thing over and over again. For example, a music box is a machine that plays the same music over and over again. Some people wanted to be able to tell their machine to do different things. For example, they wanted to tell the music box to play different music every time. They wanted to be able to program the music box- to order the music box to play different music. This part of computer history is called the "history of programmable machines" which is a fancy phrase for "The history of machines that I can order to do different things if I know how to speak their language."
One of the first examples of this was built by Hero of Alexandria (c. 10–70 AD). He built a mechanical theater which performed a play lasting 10 minutes and was operated by a complex system of ropes and drums. These ropes and drums were the language of the machine- they told what the machine did and when. Some people argue that this is the first programmable machine.[1]
Historians disagree on which early machines are "computers". Many say the "castle clock", an astronomical clock invented by Al-Jazari in 1206, is the first known programmableanalog computer. Others say the first computer was made by Charles Babbage.[2] Al - Jazari's showed the zodiac, the solar and lunar orbits, a crescent moon-shaped pointer travelling across a gateway that made some doors to open every hour,[3][4] and five robotic musicians who play music when levers hit them. The length of day and night could be changed (AKA re-programmed) every day in order to account for the changing lengths of day and night throughout the year.[2] Ada Lovelace is considered to be the first programmer.[5][6][7]

The Computing Era[change | change source]

At the end of the Middle Ages, people in Europe thought math and engineering were more important. In 1623, Wilhelm Schickard made a mechanical calculator. Other Europeans made more calculators after him. They were not modern computers because they could only add, subtract, and multiply- you could not change what they did to make them do something like play Tetris. Because of this, we say they were not programmable.
In 1801, Joseph Marie Jacquard used punched paper cards to tell his textile loom what kind of pattern to weave. He could use punch cards to tell the loom what to do, and he could change the punch cards, which means he could program the loom to weave the pattern he wanted. This means the loom was programmable.
Charles Babbage wanted to make a similar machine that could calculate. He called it "The Analytical Engine".[8] Because Babbage did not have enough money and always changed his design when he had a better idea, he never built his Analytical Engine.
As time went on, computers got more and more popular. And that stands out at the beginning. This is because people get bored easily doing the same thing over and over. Imagine spending your life writing things down on index cards, storing them, and then having to go find them again. The U.S. Census Bureau in 1890 had hundreds of people doing just that. People got bored and frustrated, and would say, "There HAS to be an easier way to do this." Then a clever person worked out how to make machines do a lot of the work. Herman Hollerith figured out how to make a machine that would automatically add up information that the Census bureau collected. The Computing Tabulating Recording Corporation (which later became IBM) made his machines, and everyone was happy. At least, they were happy until their machines broke down, got jammed, and had to be repaired. This is when the Computing Tabulating Recording Corporation invented tech support.
Because of machines like this, new ways of talking to these machines were invented, and new types of machines were invented, and eventually the computer as we know it was born.

Analog and Digital Computers[change | change source]

In the first half of the 20th century, scientists started using computers, mostly because scientists had a lot of math to figure out and wanted to spend more of their time thinking about the secrets of the universe instead of spending hours adding numbers together. For example, if they had to launch a rocket ship, they needed to do a lot of math to make sure the rocket worked right.
So they put together computers. These computers used analog circuits, which made them very hard to program. Then, in the 1930s, they invented digital computers, which made them easier to program.

High-scale computers[change | change source]

Scientists figured out how to make and use digital computers in the 1930s and 1940s. Scientists made a lot of digital computers, and as they did, they figured out how to ask them the right sorts of questions to get the most out of them. Here are a few of the computers they built:
Defining characteristics of some early digital computers of the 1940s (In the history of computing hardware)
NameFirst operationalNumeral systemComputing mechanismProgrammingTuring complete
Zuse Z3 (Germany)May 1941BinaryElectro-mechanicalProgram-controlled by punched film stockYes (1998)
Atanasoff–Berry Computer(US)mid-1941BinaryElectronicNot programmable—single purposeNo
Colossus (UK)January 1944BinaryElectronicProgram-controlled by patch cables and switchesNo
Harvard Mark I – IBM ASCC(US)1944DecimalElectro-mechanicalProgram-controlled by 24-channel punched paper tape (but no conditional branch)No
ENIAC (US)November 1945DecimalElectronicProgram-controlled by patch cables and switchesYes
Manchester Small-Scale Experimental Machine (UK)June 1948BinaryElectronicStored-program in Williams cathode ray tube memoryYes
Modified ENIAC (US)September 1948DecimalElectronicProgram-controlled by patch cables and switches plus a primitive read-only stored programming mechanism using the Function Tables as program ROMYes
EDSAC (UK)May 1949BinaryElectronicStored-program in mercury delay line memoryYes
Manchester Mark 1 (UK)October 1949BinaryElectronicStored-program in Williams cathode ray tube memory and magnetic drum memoryYes
CSIRAC (Australia)November 1949BinaryElectronicStored-program in mercury delay line memoryYes

EDSAC was one of the first computers that remembered what you told it even after you turned the power off. This is called (von Neumann) architecture.
  • Konrad Zuse's electromechanical "Z machines". The Z3 (1941) was the first working machine that used binary arithmetic. Binary arithmetic means using "Yes" and "No." to add numbers together. You could also program it. In 1998 the Z3 was proved to be Turing complete. Turing complete means that it is possible to tell this particular computer anything that it is mathematically possible to tell a computer. It is the world's first modern computer.
  • The non-programmable Atanasoff–Berry Computer (1941) which used vacuum tubes to store "yes" and "no" answers, and regenerative capacitor memory.
  • The Harvard Mark I (1944), A big computer that you could kind of program.
  • The U.S. Army's Ballistics Research Laboratory ENIAC (1946), which could add numbers the way people do (using the numbers 0 through 9) and is sometimes called the first general purpose electronic computer (since Konrad Zuse's Z3 of 1941 used electromagnets instead of electronics). At first, however, the only way to reprogram ENIAC was by rewiring it.
Several developers of ENIAC saw its problems. They invented a way to for a computer to remember what they had told it, and a way to change what it remembered. This is known as "stored program architecture" or von Neumann architectureJohn von Neumann talked about this design in the paper First Draft of a Report on the EDVAC, distributed in 1945. A number of projects to develop computers based on the stored-program architecture started around this time. The first of these was completed in Great Britain. The first to be demonstrated working was the Manchester Small-Scale Experimental Machine (SSEM or "Baby"), while the EDSAC, completed a year after SSEM, was the first really useful computer that used the stored program design. Shortly afterwards, the machine originally described by von Neumann's paper—EDVAC—was completed but was not ready for two years.
Nearly all modern computers use the stored-program architecture. It has become the main concept which defines a modern computer. The technologies used to build computers have changed since the 1940s, but many current computers still use the von-Neumann architecture.

Microprocessors are miniaturized devices that often implement stored program CPUs.
In the 1950s computers were built out of mostly vacuum tubesTransistors replaced vacuum tubes in the 1960s because they were smaller and cheaper. They also need less power and do not break down as much as vacuum tubes. In the 1970s, technologies were based on integrated circuitsMicroprocessors, such as the Intel 4004 made computers smaller, cheaper, faster and more reliable. By the 1980s, microcontrollers became small and cheap enough to replace mechanical controls in things like washing machines. The 1980s also saw home computers and personal computers. With the evolution of the Internet, personal computers are becoming as common as the television and the telephone in the household.
In 2005 Nokia started to call some of its mobile phones (the N-series) "multimedia computers" and after the launch of the Apple iPhone in 2007, many are now starting to add the smartphone category among "real" computers. In 2008, if smartphones are included in the numbers of computers in the world, the biggest computer maker by units sold, was no longer Hewlett-Packard, but rather Nokia.[source?]

Kinds of computers[change | change source]

There are many types of computers:
  1. personal computer
  2. mainframe
  3. laptop computer
  4. minicomputer
  5. supercomputer
  6. embedded system
A "desktop computer" is a small machine that has a screen (which is not part of the computer). Most people keep them on top of a desk, which is why they are called "desktop computers." "Laptop computers" are computers small enough to fit on your lap. This makes them easy to carry around. Both laptops and desktops are called personal computers, because one person at a time uses them for things like playing music, surfing the web, or playing video games.
There are bigger computers that many people at a time can use. These are called "Mainframes," and these computers do all the things that make things like the internet work. You can think of a personal computer like this: the personal computer is like your skin: you can see it, other people can see it, and through your skin you feel wind, water, air, and the rest of the world. A mainframe is more like your internal organs: you never see them, and you barely even think about them, but if they suddenly went missing, you would have some very big problems.
An embedded computer, also called embedded system is a computer that does one thing and one thing only, and usually does it very well. For example, an alarm clock is an embedded computer: it tells the time. Unlike your personal computer, you cannot use your clock to play Tetris. Because of this, we say that embedded computers cannot be programmed, because you cannot install more programs on your clock. Some mobile phonesautomatic teller machinesmicrowave ovensCD players and cars are operated by embedded computers.

All-in-one PC[change | change source]

All-in-one computers are desktop computers that have all of the computer's inner mechanisms in the same case as the monitorApple has made several popular examples of all-in-one computers, such as the original Macintosh of the mid-1980s and the iMac of the late 1990s and 2000s.

Common uses of home computers[change | change source]

Common uses of work computers[change | change source]

  • Word processing
  • Spreadsheets
  • PowerPoint Presentations
  • Photo Editing (Photoshop, GIMP)
  • E-mail
  • Video editing/rendering/encoding
  • Audio recording
  • System Management
  • Excel

Working methods[change | change source]

Computers store data and the instructions as numbers, because computers can do things with numbers very quickly. These data are stored as binary symbols (1s and 0s). A 1 or a 0 symbol stored by a computer is called a bit, which comes from the words binary digit. Computers can use many bits together to represent instructions and the data that these instructions use. A list of instructions is called a program and is stored on the computer's hard disk. Computers work through the program by using a central processing unit, and they use fast memory called RAM as a space to store the instructions and data while they are doing this. When the computer wants to store the results of the program for later, it uses the hard disk because things stored on a hard disk can still be remembered after the computer is turned off.
An operating system tells the computer how to understand what jobs it has to do, how to do these jobs, and how to tell people the results. Millions of computers may be using the same operating system, while each computer can have its own application programs to do what its user needs. Using the same operating systems makes it easy to learn how to use computers for new things. A user who needs to use a computer for something different, can learn how to use a new application program. Some operating systems can have simple command lines or a fully user-frendly GUI.

The Internet[change | change source]

One of the most important jobs that computers do for people is helping with communication. Communication is how people share information. Computers have helped people move forward in sciencemedicinebusiness, and learning, because they let experts from anywhere in the world work with each other and share information. They also let other people communicate with each other, do their jobs almost anywhere, learn about almost anything, or share their opinions with each other. The Internet is the thing that lets people communicate between their computers.

Computers and waste[change | change source]

A computer is now almost always an electronic device. It usually contains materials that will become toxic waste when disposed of. When a new computer is bought in some places, laws require that the cost of its waste management must also be paid for. This is called product stewardship.
Computers can become obsolete quickly, depending on what programs the user runs. Very often, they are thrown away within two or three years, because newer programs require a more powerful computer. This makes the problem worse, so computer recycling happens a lot. Many projects try to send working computers to developing nations so they can be re-used and will not become waste as quickly, as most people do not need to run new programs. Some computer parts, such as hard drives, can break easily. When these parts end up in the landfill, they can put poisonous chemicals like lead into the ground water. Hard drives can also contain secret information like credit card numbers. If the hard drive is not erased before being thrown away, an identity thief can get the information off of the hard drive, even if the drive doesn't work, and use it to steal money from the previous owner's bank account.

Main hardware[change | change source]

Computers come in different forms, but most of them have a common design.
  • All computers have a CPU.
  • All computers have some kind of data bus which lets them get inputs or output things to the environment.
  • All computers have some form of memory. These are usually chips (integrated circuits) which can hold information.
  • Many computers have some kind of sensors, which lets them get input from their environment.
  • Many computers have some kind of display device, which lets them show output. They may also have other peripheral devices connected.
A computer has several main parts. When comparing a computer to a human body, the CPU is like a brain. It does most of the 'thinking' and tells the rest of the computer how to work. The CPU is on the Motherboard, which is like the skeleton. It provides the basis for where the other parts go, and carries the nerves that connect them to each other and the CPU. The motherboard is connected to a power supply, which provides electricity to the entire computer. The various drives (CD drive, floppy drive, and on many newer computers, USB flash drive) act like eyes, ears, and fingers, and allow the computer to read different types of storage, in the same way that a human can read different types of books. The hard drive is like a human's memory, and keeps track of all the data stored on the computer. Most computers have a sound card or another method of making sound, which is like vocal cords, or a voice box. Connected to the sound card are speakers, which are like a mouth, and are where the sound comes out. Computers might also have a graphics card, which helps the computer to create visual effects, such as 3D environments, or more realistic colors, and more powerful graphics cards can make more realistic or more advanced images, in the same way a well trained artist can.

Largest Computer Companies[change | change source]


Company nameSales
(US$ billion)
South Korea Samsung212,680
United States Apple220,000
Republic of China Foxconn132,070
United States HP (Hewlett-Packard)112,300
United States IBM99,750
Japan Hitachi87,510
United States Microsoft86,830
United States Amazon74,450
Japan Sony72,340
Japan Panasonic70,830
United States Google59,820
United States Dell56,940
Japan Toshiba56,200
South Korea LG54,750
United States Intel52,700

Popular Read Article